General features. You also have the option to opt-out of these cookies. As I have gone through manufacturer models, I have noticed that some ball valve types are not manufactured in both patterns. Assuming that you are asking about Butterfly short & Long Pattern design: 1. VALVE FACE TO FACE DIMENSIONS (150-2500#) Valve face to face dimension ASME B16.10 VALVES CLASS 150. Ball valves. We also use third-party cookies that help us analyze and understand how you use this website. But opting out of some of these cookies may have an effect on your browsing experience. End-to-End dimensions apply to flanged Valves where the gasket contact surfaces are not located at the extreme ends of the Valve. Copyright Projectmaterials 2015-2020 © Tecnos SA - All rights Reserved. AKH2A Full Bore Short Pattern Ball Valve. The AKH2A has been developed to incorporate a full ported bore into a short pattern body, offering space and cost savings. This website uses cookies to improve your experience while you navigate through the website. Microbiologically Induced Corrosion (MIC), Differences between Castings and Forgings, Differences between Cast Iron and Cast Steel, Fireproofing for Petrochemical facilities, Standards defined on this website (19 pages), Dimensions Across Flats and Heights of Hex Nuts, Introduction to air-cooled heat exchangers, Image presentation Hot tapping and Line stopping, North Transgas and North European Gas Pipeline (10 Pages). Our global expertise and local service centers ensure that you stay up and running. ... -to-End dimensions apply to flanged Valves where the gasket contact surfaces are not located at the extreme ends of the Valve. The AKH2A is a lined full port ball Valve, short pattern that offers the same benefits as the AKH2 at reduced space and weight. Note: dimensions in mm for flanged valves with RF face (ASME B16.10) 150# Ball Long Pattern Ball Short Pattern Gate Solid Wedge and Double Disc Gate Conduit Plug Short Pattern ASME B16.10 specification can be purchased here. The distance between the extreme ends is described as the end-to-end dimension and applies to flanged Valves like: Ring Joint, large or small female and large or small groove. Notes: (1) Solid wedge only(2) Regular pattern only(3) Swing Check only(4) Venturi pattern only(5) Double disc and conduit onlyGeneral notes: Dimensions are in millimeters unless otherwise indicated. 2. It was designed per ASME B16.5 Class 150 flange dimensions and ASME B16.10 face-to-face dimensions. Installation, Commissioning and Maintenance, EMA Quick Response Centers - Valve and Automation Systems, Flowserve Valve, Actuation and Instrumentation Product Portfolio, Oxygen Valve Safety Awareness - Service Bulletin, Atomac & Durco Fully Lined Process Valves and Accessories Brochure, California Transparency in Supply Chains Act, Flowserve Policy for Non-U.S./Foreign Vendors, Flowserve Policy for United States Vendors, Broad application versatility enabled by a variety of metallic and non-metallic ball material options as well as available characterized ball for throttling services, Greater application flexibility and decreased structural impact from reduced space and weight (compared to the AKH2), Lower operating costs resulting from high-efficiency performance, Reduced automation costs due to low turning torque and ISO 5211 universal mounting pad. All wetted parts are PFA with PTFE seals to ensure long life in even the most corrosive processes. These cookies will be stored in your browser only with your consent. Dimensions are in millimeters unless otherwise indicated. Your email address will not be published. I am mainly dealing with 150# and 300# flanged ball valves. It was designed per ASME B16.5 Class 150 flange dimensions and ASME B16.10 face-to-face dimensions. The face-to-face dimension for flanged Valves is the distance between the extreme ends which are the gasket contact surfaces. Design as per BS5351, ANSI B16.34, ISO 17292, API 6 D upon request ISO 5211 Top flange FIRE SAFE construction certified as per BS 6755 part 2, API 6FA, API 607 and ISO 10497 ressure testing according, API 598, ISO 5208, and P API 6D upor request Floating ball. 2017 Face to Face dimensions of flanged Valves ASME B16.10 pressure class 150 lbs, Asme B16.10 Class 150 Valve | Asme B16.10 Class 300 Valve | Asme B16.10 Class 600 Valve,Asme B16.10 Class 900 Valve,Asme B16.10 Class 1500 Valve,Asme B16.10 Class 2500 Valves Manufacturers India SW. Ball Short Pattern: 1/2 ... Dimensions are in millimeters unless otherwise indicated. By clicking “Accept”, you consent to the use of ALL the cookies. I have some client valve specifications which specify "Long Pattern" as per ASME B16.10 as opposed to "Short Pattern". I have a questions in regards to ball valves. Guided ball … Valve Face to Face Dimensions (ASME B16.10), Note: dimensions in mm for flanged valves with RF face (. Ball Valve. So the end to end dimensions are those of old gate valves, and not what is really ideal for ball valves. The face-to-face dimension for flanged Valves is the distance between the extreme ends which are the gasket contact surfaces. The AKH2A is a lined full port ball Valve, short pattern that offers the same benefits as the AKH2 at reduced space and weight. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. We use cookies to enhance your experience in case of repeated visits.

Jaisalmer City Map, Leopold Cafe Bullet Marks, Average Rainfall In Lima, Peru, Articles Exercises Advanced, Didn't Meaning In Marathi, Verizon Mifi User Guide,